Sawing takes a lot of expertise to be carried out. Among different woodworking saws, a miter saw is the most basic one and by far the easiest to use. A miter saw is no wonder an extremely handy tool for woodworkers. Whether it is different lumber crosscuts, crown molding, or repetitive cuts, a miter saw is just the right tool you need.
Not only that, but a miter saw is also easily maneuverable and beginner-friendly. Thus, even if you are new to woodworking, it would be great for you to use. However, there are some tips and tricks that you should know while using a miter saw. The miter saw safety tricks makes the handling of a miter saw even easier than ever!
In this blog, we researched and bought you the best 8 miter saw tips and tricks so that you do not fall back in knowing about miter saw tools.
Miter Saw Tips and Tricks
The chances of getting a newly bought miter saw the board in good shape is pretty thin. Even before handing over to you, the saw has probably gone through a rigorous time. They have probably been moved a couple of times for various reasons. Finding a great quality and unhampered piece of the miter saw that did not go through some moving is a hard find.
Having a miter board with uneven and chipped edges is not something uncommon. But cutting in such conditions is not favorable at all. That is why you need to know some miter saw tips and tricks and get the tools in perfect condition.
Firstly, examine the edges of the board and see where it is chipped. Only cut the parts which are damaged. I almost always smooth the sides and edges of each tool I purchase. This allows smooth cuttings too.
Want to make cutting with your saw more efficient? The best way to increase its efficiency is using a miter saw stop block system. The only time you should not use stop blocks is for single cuts, which are pretty uncommon in woodworking. But for woodworks like 4 legged tables or chairs and many many more things that require multiple cuts, using stop blocks is the best way to do them smoothly.
And as of the setting of the stop blocks, it is quite simple. Determine the length of your workpieces. Now, clamp a scrap of wood in the place where you need to attach your workpiece. Then, you can start cutting as soon as you line up the board with the used stop blocks. You are certain to get the same dimensional pieces in this manner.
Fences are without any doubt the most safe way for molding woods. Stop blocks also work great but if you have workpieces longer than your saw’s fence, what should you do? You can surely use this miter saw safety tips to extend your fences.
You may see some holes in the fences but do not know what they are used for. You can attach a straight board to your miter saw’s fence through there. For added safety, add some screws at that place so that they do not stick outside. Moreover, on each side of the blade split, be sure to drive two screws and maintain a tightness.
Even, adding a fence extension brings some extra benefits for you. The extension fences help in cleaner cuts with a lot less splintering by creating a zero clearance slot.
And once you are done extending the fences, you should be able to add stop blocks throughout the length of your workpiece. Moreover, you can measure the length of your cuts by clipping a measuring tape which is a great thing! Now, you just need to mark the fence, place your stop blocks accordingly, clamp your workpiece in the right place, and get your cuttings started!
If you already have a liking for the clean cuts due to the extended fence, having an improvement in the table of the saw would help too. Having an improved table will also bring the same type of precision.
Most of the miter saws come with a very wide throated insert blade creating a for the tilted blades when making bevel cuts. But, while cutting smaller pieces, this may cause some significant problems. The workpiece may not have even finish or even the small pieces may get into the slots.
In order to have a smooth miter saw table, you can follow this suggestion among so many miter saw tips and tricks. You can attach a layer of plywood over the table in just the right size of your original table. If you want to keep it in place, slide it over the fence and screw in the extension fence on its top like somewhat clamping it.
Or you can use a double-sided carpet tape too. This also helps in keeping the board in place.
You will find plenty of miter saw use tips for making wider cuts. Although working with longer pieces is fairly easy, working with small pieces is not a very handy one. So, here’s one miter saw tips and tricks for small workpieces.
You may need to cut smaller wood pieces at times. Even one might need to cut dowel pins some times. Cutting wider cuts on longer woods is easily maneuverable. It is fairly easy to get smooth too. However, while cutting smaller pieces is a lot harder. You even have chances of getting cuts on your hands while handling smaller woods.
One thing you must do is holding the small pieces in place. You can use a long wood piece to hold the smaller one in place. Or you can use a pencil to hold it in place. This is a great way to keep your fingers in a safe distance.
Stop Blocks are surely very helpful to create cuts. However, at times when you need to make one-off cuts, the need for stop blocks is minimal. Using a measuring tape, measure the length of and make a line on the board with a marker. Also, keep the thickness of the blade or the thickness of the kerf in mind too.
Common mistake amateurs do is drawing the line and start cutting right from the middle. This tends to leave the board a bit shorter than you initially intended. If the thickness of your blade is 1/8th of an inch, you are likely to get cuts 1/16 inch smaller than you drew.
In order to have straight and even lines, keep in mind where the measuring of the line begins. Ans start cutting from one edge rather than starting at the middle of the line. If you do not start in this way, you will have a shorter cut. Thus, it would affect the final product of your work.
In this blog of miter saw tips and tricks, we gave a great emphasis on the sawing board. And it is not without a reason. For accuracy in cuttings, the need for a great miter saw table is unparalleled.
Sometimes, when you do your work, you may find that your saw table is slightly longer than your need. It could be the cross brace for that table top and it needs to be fitted perfectly. A way to make things better is by the shaving of a very little amount of wood from one edge of the board.
This will press the board ends up against the saw blade which will help the board flex a little bit more. Now, hold the board in a place and raise the blade in an upright position and ensure its standing. Upon bringing it down, you should be able to cut just what you want.
Without spending huge sums for the perfect fit, shaving off the board is a great way to get the right size cuts.
Miter saws are great for any woodworkers, even if they are beginners. It just seems like the most usable piece of tool. However, there is one limitation many avid woodworkers face with miter saws. It is the problem with cutting wider boards. The widest board almost all the miter saws are able to cut is just a bit over the radius of its blade. It is this way due to the position of the fence and the way of the hanging of its head.
Sometimes, woodworkers find some boards that can be cut up to an extent and not more than that. This makes woodworking a lot more harder than it supposedly is.
You would find many miter saw tips and tricks in this regard. I personally suggest this small trick. Use a scrap wood piece to raise the main working wood a bit above the board. This would help in getting a wider cut than the previous way.
Additional Miter Saw Tips And Tricks
The above mentioned 8 miter saw tips and tricks are used by pros. But if you are a beginner, you may take note of the additional miter saw tips and tricks we have put together for you.
Miter saws can be fairly heavy to be carried around. If you have it fixed in a place, moving with it is a problem. That is why a miter saw stand is a must for sure. However, it is wise to ensure a mobile miter saw stand. This would make your work easier if you need to transport the saw from one place to the other.
Nowadays, you would find a number of top quality miter saws with a pre-installed laser guide. And it is not just for show. The laser guides in most of the saws are what ensures accuracy in your cuttings. Following the laser guide ensures your cuts are done according to the line you drew.
If you have an old model miter saw, do not worry. You can buy an additional laser and attach it to the saw. Just at the place where the washer is connected to the blade, remove the washer, and add the laser there.
While cutting with a saw, you would want it to be at its full-speed for precise cuts. So, it is better to wait just a couple of seconds after powering on the saw. It takes a couple of seconds for some models to jerk off and come to its full potential.
However, for a rather high-end miter saw, they come with a smooth start which allows the blade to gain full speed without any hiccups. Those are great too!
If you are using a compound miter saw, you should not be unknown to the blade changing. And undoubtedly, it takes a lot more time than you would expect. So, what is needed to fasten this process?
A Blade Wrench! It helps in an easy change of blades without many complications. It is better for everyone to ensure a blade wrench when purchasing a miter saw.
It is not unknown to us how easily a saw blade can turn in to your worst nightmare! That is why it is essential to ensure safety while using a miter saw.
While buying a miter saw, always ensure a few safety features like the blade guard, blade brake, and double trigger start-up switch to be sure of your safety.
Miter saw surely is a great tool that is easy to use. It is helpful for woodworkers due to its ease of use. But, there are some cases like extending fence, cutting wider tables, using stop blocks, etc which you need to master in order to get the best cuttings. That is why we bought this blog of the most important miter saw tips and tricks so that you can also work like a pro!